# TIP31C TO-220 NPN Transistor

- Link: https://gssuperstore.in/product/tip31c-to-220-npn-transistor/
- Published: 2026-08-03T09:45:48+05:30
- Author: Karan7055

TIP31C TO-220 NPN transistor delivers reliable medium-power switching and amplification
in a compact, industry-standard package trusted by engineers and hobbyists alike.
With a continuous collector current rating of 3A and a collector-emitter breakdown
voltage of 100V, this transistor handles a wide range of DC motor drives, relay 
drivers, lamp controls, and audio amplifier stages with ease. The robust TO-220 
package provides excellent thermal dissipation, especially when paired with a suitable
heat sink, making it a dependable workhorse for both prototype and production designs.

## Key Features

 * **NPN silicon transistor** in industry-standard TO-220 package for easy through-
   hole mounting
 * **100V collector-emitter breakdown voltage (VCEO)** — suitable for higher-voltage
   switching applications
 * **3A continuous collector current (IC)** — handles medium-power loads without
   additional components
 * **40W power dissipation** with heat sink — significantly higher than small-signal
   transistors
 * **DC current gain (hFE) of 10–50** across a wide collector current range for 
   predictable operation
 * **Complementary pair with TIP32C** (PNP) — ideal for push-pull and H-bridge circuit
   designs
 * **RoHS-compliant construction** — meets modern environmental standards
 * **Mounting tab at ground potential** (collector) — allows direct heatsinking 
   without insulating pads in many circuits

## Specifications

  |  Parameter |  Value |  
   |  Transistor Type |  NPN Silicon |  
 |  Package |  TO-220 |  
 |  Collector-Emitter Voltage (VCEO) |  100V |  
 |  Collector-Base Voltage (VCBO) |  100V |  
 |  Emitter-Base Voltage (VEBO) |  5V |  
 |  Continuous Collector Current (IC) |  3A |  
 |  Peak Collector Current (ICM) |  5A |  
 |  Base Current (IB) |  1A |  
 |  DC Current Gain (hFE) |  10–50 (@ IC = 1A) |  
 |  Collector-Emitter Saturation Voltage (VCE sat) |  ≤ 1.2V (@ IC = 3A, IB = 0.3A) |  
 |  Power Dissipation (PD) — with heat sink |  40W |  
 |  Power Dissipation (PD) — free air |  2W |  
 |  Transition Frequency (fT) |  3 MHz (typ.) |  
 |  Operating Junction Temperature (TJ) |  –65°C to +150°C |  
 |  Storage Temperature (Tstg) |  –65°C to +150°C |  
 |  Thermal Resistance (junction to case) θJC |  3.125°C/W |  
 |  Pin Configuration (front view) |  Base | Collector | Emitter |  
 |  Complementary PNP Type |  TIP32C |  
 |  Compliance |  RoHS |

## Compatible Applications

 * DC motor speed control circuits (PWM-driven)
 * Relay driver stages (12V and 24V coils)
 * Solenoid and valve drivers
 * Lamp and LED driver circuits (up to 3A loads)
 * Audio power amplifier output stages
 * Push-pull and H-bridge configurations (with TIP32C)
 * Linear voltage regulator pass elements
 * Switch-mode power supply (SMPS) circuits
 * Arduino, Raspberry Pi, and microcontroller load switching
 * Industrial control and automation circuits

## Installation Guide

### General Through-Hole PCB Installation

 1. Identify the three pins from the front (label side): **Base (B)**, **Collector (
    C)**, **Emitter (E)** — left to right.
 2. Insert the transistor into the corresponding PCB footprint, ensuring correct pin
    orientation.
 3. If required, bend the leads at 90° for horizontal (lying flat) mounting.
 4. Solder each pin and trim excess lead length.
 5. If power dissipation exceeds 2W, attach a TO-220 compatible heat sink to the metal
    tab before powering the circuit.

### DC Motor Driver (Microcontroller)

 1. Connect the **Base** pin through a 1kΩ–10kΩ resistor to the microcontroller GPIO
    output pin.
 2. Connect the **Collector** to the negative terminal of the motor (motor’s other 
    terminal goes to the supply rail).
 3. Connect the **Emitter** to GND.
 4. Place a flyback diode (e.g., 1N4007) across the motor terminals (cathode to supply,
    anode to collector) to suppress inductive voltage spikes.
 5. Apply PWM signal to the base resistor to control motor speed.

### Relay Driver

 1. Connect the **Base** through a current-limiting resistor (typically 1kΩ) to the
    control signal.
 2. Connect the **Collector** to one terminal of the relay coil.
 3. Connect the other terminal of the relay coil to the supply voltage (VCC).
 4. Connect the **Emitter** to GND.
 5. Add a flyback diode in parallel with the relay coil to protect against back-EMF.

### Heat Sink Mounting

 1. Apply a thin, even layer of thermal paste to the metal tab of the TIP31C.
 2. Align the tab with the heat sink mounting hole.
 3. If the circuit requires the collector to be electrically isolated from the heat
    sink, insert a TO-220 insulating mica or silicone pad between the tab and heat 
    sink.
 4. Secure with an M3 screw and nut — do not overtighten.
 5. Verify electrical isolation with a multimeter if an insulating pad was used.

Whether you are building a motor controller, relay driver, or audio amplifier, the
TIP31C TO-220 NPN transistor gives you the headroom, reliability, and thermal performance
to do it right. Add it to your order today and keep your projects moving forward.
